How do I install a wired flow sensor or flow sensor? (Generation 2)

Note

Need help adding a wired flow meter to your Rachio 3? Go here!

Looking for Installation Steps for the Rachio Wireless Flow Meter? Need help installing a flow meter? Complete the form below to be connected with a local Rachio Pro!

DISCLAIMER

While the flow sensors listed below are manufactured by BADGER, CST, or TORO, Rachio is NOT affiliated or authorized by these entities. This article is intended for instructional and compatibility purposes only.


Flow Sensor Compatibility

Flow sensors monitor the actual flow of water running through a pipe; this allows the controller to record and report your sprinkler's actual water consumption in gallons. The Rachio Generation 2 Smart Sprinkler Controller is compatible with the following flow sensors:

Badger

  • 228PV15
  • 228PV20
  • 735PV75

CST

  • FSI-T10-001
  • FSI-T15-001
  • FSI-T20-001

Toro

  • TFS-050
  • TFS-075
  • TFS-100
  • TFS-150
  • TFS-200

Note

Please note: The Rachio Generation 1 Smart Sprinkler Controller is not compatible with wired flow sensors. For the best in flow monitoring and leak detection, we recommend the Rachio Wireless Flow Meter. Want to upgrade to a Rachio 3 with Wireless Flow Meter? Go here!

Go to Top ^


Flow Sensor Installation

Note

Want to add a wired flow meter to your Rachio 3? Go here!

To connect a flow sensor to your Rachio Generation 2 controller, please see the wiring diagram below (note the red & black wires MUST be installed correctly for the data to send to the controller).

Note

Either terminal "S1" or "S2" can be used for the flow sensor. Configuration in the app allows you to assign a rain sensor or a flow sensor to either terminal.

Go to Top ^


How to enable a Flow Sensor

To configure the flow sensor in the Rachio app, please follow the steps below:
1) From the More tab, select "Accessories."
2) Select the sensor terminal you wish to configure - "Sensor (S1 Terminal") or "Sensor (S2 Terminal)"

Accessories

3) Enable the sensor and select the type of sensor you're adding; in this case "Flow"
4) Select your flow sensor from the list.

Go to Top ^


Flow Sensor Reporting (Gallons)

If the flow sensor is enabled via the controller settings, the usage reports in the mobile and web app will report in gallons. The gallons reported are absolute units; if the flow sensor is malfunctioning, the gallons reported will represent the measured gallons from the flow sensor.

MOBILE APP

Mobile App

WEB APP

Screen_Shot_2018-03-20_at_12.05.42_AM.png

Go to Top ^


What if my usage reports seem high?

If your water usage seems high after connecting a flow sensor, the likely culprit a wiring error or faulty wire. You can follow these steps to debug the issue.

Note

This test will require a multi-meter to debug.

If all zone runs are measuring high usage:

Set your multimeter to measure resistance.

1) Measure the resistance between the C and SC ports on the controller. If this resistance is below 1k ohms, you have a short circuit between C and SC which needs to be disconnected.

2) Measure the resistance between C and S1 or S2, whichever has your flow sensor connected. If this resistance is below 1k ohms, you have a short circuit between C and S1/2 which needs to be disconnected.

If only one zone run is measuring high usage:

1) Set your multimeter to measure resistance.

2) Measure the resistance between the zone number that’s failing and SC ports on the controller. If this resistance is below 1k ohms, you have a short circuit which needs to be disconnected.

3) Measure the resistance between the zone number that’s failing and S1 or S2, whichever has your flow sensor connected. If this resistance is below 1k ohms, you have a short circuit which needs to be disconnected.

Go to Top ^


Why aren't my drip zones recording flow?

There is a lower limit to all flow sensors. If your drip zone is below this limit (most are), your Rachio controller cannot measure any flow and will revert to estimated usage. You can find the limits of each flow sensor below:

TORO

CST

Go to Top ^


Can I get notifications for high flow? [BETA]

High flow notications are currently in beta testing. If you'd like to participate, please sign up using the button below.

Was this article helpful?
25 out of 30 found this helpful

Have more questions? Submit a request

Comments

0 comments

Article is closed for comments.